无催化纳米氧化锌的制备及其光学性质研究

本文采用无催化剂直接蒸发高纯Zn粉,在800℃氧气氛条件下,在Si(111)衬底上生长得到以四角状为主的纳米ZnO(T-ZnO)。T-ZnO纳米线每个角约互成110°,长度约为1.5μm,直径100nm左右;Raman分析表明E2(H)普遍存在于各形态的ZnO;光致发光光谱表明,T-ZnO纳米线的光致发光除了与材料性质有关,还与杂质缺陷有关,蓝绿光带是ZnO的缺陷产生的。     

宽带放大器用碲基掺铒光纤结构参量的设计考虑

利用光波导理论及均匀展宽四能级模型，研究了宽带放大器用阶跃型折射率分布碲基掺铒光纤的结构参量—纤芯半径和相对折射率差的设计考虑.理论研究表明，在单模传输条件下，为获取最大信号增益，宜选择相对折射率差大的碲基掺铒光纤来构建光纤放大器.相对折射率差一定的情况下，在高泵浦功率、小信号输入或光纤长度短于各信道最佳增益长度时，选择纤芯半径大的碲基掺铒光纤可以得到大的信号增益；反之，宜选择纤芯半径小的碲基掺铒光纤.     

基于支持向量机的肤色滤波器

为了探测图像中的肤色像素，提出了一种新的方法-支持向量机（SVM：Support Vector Machine）方法.它是一种基于肤色的非特定人的面部定位方法，是非接触人机交互技术和机器视觉中的一个重要内容.实验结果表明，采用支持向量机方法较传统人工神经网络方法不仅有更高的探测准确性，而且具有更好的推广性能.由于SVM采用结构风险最小化（SRM：Structural Risk Minimization）准则，在最小化训练误差（经验风险）的同时，尽量缩小模型预测误差的上界，从而使模型有更好的泛化能力.     

制冷机冷却型小型超导强磁场系统的研制

介绍了一套制冷机冷却型小型超导强磁场系统。超导磁体线圈用铌钛超导线绕制,室温孔直径为75mm,磁场中心Φ25mm×250mm区域内最高场强达到3.64T,磁场不均匀性小于3%。在2.62T场强下连续闭环运行了20天,电流衰减率近似为零。采用4K级低温制冷机冷却防辐射冷屏,液氦蒸发率小于0.03升/小时,系统一次可注入液氦50升,补液周期大于60天。     

实验数据中的坏值及剔除方法

本文对实验得出的数据采用数理统计的方法进行判断,确定测试结果的正确性;对测试结果出现的坏值应给予剔除。     

INERTIAL MANIFOLDS FOR NONAUTONOMOUS SEMILINEAR PARABOLIC PARTIAL DIFFERENTIAL EQUATIONS WITH TIME DELAYS

The present paper deals with the long-time behavior of a class of nonautonomous retarded semilinear parabolic differential equations. When the time delays are small enough and the spectral gap conditions hold, the inertial manifolds of the nonautonomous retard parabolic equations are constructed by using the Lyapunov-Perron method.     

公务员最优录用分配方案的数学模型

本文通过建立0-1规划模型,设计了一种公务员招聘中的最优录用分配方案,并运用L INGO软件求得了一个实际问题的最优解.     

Widely tunable long-period fiber grating with nm-thick higher refractive index film overlay

By introducing a four-layer step-index waveguide modeling, the characteristics of long-period fiber grating (LPFG) with an nm-thick film overlay, which has higher refractive index than that of fiber cladding are investigated in detail. The influence of both the overlay thickness and refractive index on the tuning ability of LPFG is analyzed. The numerical results demonstrate that spectral response of LPFG is divided into three distinct regions as the overlay deposition increases and the shift of resonant wavelength is drastic in some special thickness range. In conjunction with higher-order cladding mode coupling and fiber cladding etching, the sensitivity of LPFG to the overlay refractive index is enhanced significantly and over 120 nm resonant wavelength tunable range is achieved.     

The effect of microscopic features upon the transmissivity of enclosed laser ablated laminated metallised polymer films

A vacuum-deposited aluminium layer (20 nm) is sandwiched between two layers of laminated oriented polypropylene (OPP) film whose thickness varies from 20 to 40 μm. Selected areas of this sealed system were transparentised by the redistribution of the aluminium layer without breaking the seal or causing damage to the OPP film using a 75 W Q-switched Nd:YAG laser. The resultant transparentised films contain aluminium particles, distorted polymer areas and intact areas of the vacuum-coated aluminium layer. This paper investigates the effect of microscopic features upon the overall transmissivity of the laser-treated films and hence the quality of the transparentisation process.     

双面金属包覆介质波导模序数的判别方法

在双面金属包覆介质波导中 ,随着介质层厚度的变化 ,会出现TM0 模与TM1 模的分离和简并两种状态 ,从而影响衰减全反射 (ATR)谱中模序数的确认。通过对金属波导的理论分析和实验研究 ,提出了三种模序数确认方法 :本征角计算法、吸收峰全峰半宽比较法和吸收峰峰间距比较法 ,实现了两种状态下对模序数的准确判断